Top 10 Raspberry Pi Temperature Sensor – Temperature Probes & Sensors

As an Amazon Associate I earn from qualifying purchases.

1. Weewooday


Compatible with Raspberry Pi, 4 Sets DS18B20 Temperature Sensor Module Kit with 1 m/ 3.2 Ft Waterproof Digital Stainless Steel Probe -55 to +125 Degrees Celsius

Weewooday #ad - Parameter information: power supply: 3. 0v - 5. 5v; adjustable resolution: 9 - 12 bit; temperature range: -55 ℃ to +125 ℃; Output : red VCC, yellow DATA, black GND. Ds18b20 temperature sensor: the size of stainless steel housing is approx.

1 m/ 39. 4 inch, which is long enough to meet your needs. What you get: you will get 4 ds18b20 temperature sensors, 4 adapter modules and 4 female to female jumper wires; The adapter module has a pull-up resistor, which can be directly connected to the GPIO for Raspberry Pi without an external resistor. Quality material: the probe is made of quality stainless steel material, moisture-proof and not easy to rust, which is waterproof, so as to prevent short circuits.6

6 x 50 mm/ 02 x 2 inch, and the digital temperature thermal cable has a total length of approx. Wide application: this ds18b20 temperature sensor is compatible with Raspberry Pi, and is widely applied in temperature monitoring of cable trench, boiler, agricultural greenhouse, clean room, zer, etc.
BrandWeewooday #ad
ManufacturerWeewooday #ad
Part NumberWeewooday-Pieces Color-X047



ICQUANZX 2pcs DS18B20 Temperature Sensor Module Kit with Waterproof Stainless Steel Probe for Raspberry Pi

ICQUANZX #ad - Measure the temperature directly in water or soil. Pull-up resistor included on the adapter module, an external resistor is not required to connect directly to the GPIO of the Raspberry Pi. Simplify connecting a waterproof temperature sensor to your project with this adapter module kit. Ds18b20 wiring: red = vcc, yellow = Data, Black = GND. Waterproof digital temperature sensor DS18B20 on 100cm cable with adapter module.
ManufacturerICQUANZX #ad

3. HiLetgo


HiLetgo DHT22/AM2302 Digital Temperature and Humidity Sensor Module Temperature Humidity Monitor Sensor Replace SHT11 SHT15 for Arduino Electronic Practice DIY

HiLetgo #ad - Humidity measuring range: 0~100%RH, Humidity measurement accuracy: ±2%RH. Main chip: aosong am2302 high Sensitive Temperature Humidity Sensor. Single-bus digital signal output, bidirectional serial data. With fixing screw hole, convenient to install and fixed. Temperature range: -40 to 80 degree celsius, Temperature measurement accuracy: +/- 05℃ degree celsius.
BrandHiLetgo #ad
ManufacturerHiLetgo #ad
Weight0.01 Pounds
Part Number3-01-1190

4. Songhe


Songhe DHT11 Digital Temperature and Humidity Sensor Module for Arduino Raspberry Pi 2 3 5pcs

Songhe #ad - Dht11. Operating voltage 3. 3v-5v. Temperature measuring range: 0 degrees -50 degrees temperature measurement error: + - 2 degrees. Output type Digital Output. Humidity measuring range: 20% -95% range 0 degrees -50 degrees and humidity measurement error: + - 5%.
BrandSonghe #ad
ManufacturerSonghe #ad
Height0.2 Inches
Length1.26 Inches
Width0.55 Inches
Part NumberH56S

5. SunFounder


SunFounder DS18B20 Temperature Sensor Module Compatible with Arduino and Raspberry Pi

SunFounder #ad - The sensor uses a 1-wire bus and outputs temperature data. A temperature sensor module that uses a DS18B20 Temperature Sensor. Working voltage: 3. 3-5v dc; pcb size: 2. 0 x 2. 0 cm. Directly output temperature values in Celsius. Temperature measurement range: -55℃ ~ +125℃, with an inherent error of 1℃. Small-sized, low-cost hardware, strong capacity of resisting disturbance, high precision.
BrandSunFounder #ad
ManufacturerSunFounder #ad
Height0.16 Inches
Length0.79 Inches
Weight0.02 Pounds
Width0.79 Inches
Part NumberSF-DS18B20



2 Pack DS18B20 Temperature Sensor Module Kit with Waterproof Stainless Steel Probe, TO-92 for Arduino and Raspberry Pi

MICREEN #ad - Temperature sensor module kit: pull-up resistor included on the adapter module, connect directly to the GPIO of the Raspberry Pi. What you get: 2 set temperature sensor module kit ds18B20 temperature sensor, pluggable terminal adapter, 3pin cable and 2 pcs DS18B20 TO-92.

After-sale service: if you have any questions, please feel free to contact or QA us, we will provide you satisfied solutions. Suitable for: stainless steel probe can measure the temperature directly in water or soil and it is widely used in temperature monitoring for fish tanks, machinery, equipment, greenhouses. Ds18b20 to-92: programmable resolution 1-Wire Digital Thermometer Need to be used with pull-up resistor.
BrandMICREEN #ad
ManufacturerMICREEN #ad
Part NumberMICREEN-DTSMK-050701

7. NESPi


AVR, Sinkr DS18B20 Temperature Sensor Module Kit Waterproof Temperature Probe with Heat Resistance Thermal Cable Suitable for a Wide Range of Temperature for Arduino,Raspberry Pi, MCU, MSP430

NESPi #ad - This thermometer is suitable for a wide range of temperature from -55°C to 125°C. Widely applications: thermostatic controls, consumer products, thermometers, any thermally sensitive system, industrial systems, etc. Power supply range:3. 0v to 5. 5v. Programmable resolution 1-Wire Digital Thermometer, No other components, unique single bus interface. Data transmission mode: 9 - 12 adjustable resolution. Apply to arduino, raspberryPi, MCU. Stainless steel shell: 6 x 50mm Diameter x Length, length of cable:100cm. No a/d converter is required.
BrandNESPi #ad
ManufacturerSinkr #ad
Part NumberDS18b20

8. HiLetgo


HiLetgo 2pcs LM75 LM75A Temperature Sensor Module High Speed I2C IIC Interface High Precision Temperature Sensor

HiLetgo #ad - Lm75a or b is a high-speed I2C interface temperature sensor that converts temperature directly to digital signals. Lm75 temperature sensor high Speed I2C IIC Interface temperature sensor. Lm75a has three selectable logic address pins that allow eight devices to be connected simultaneously on the same bus without address conflicts.
BrandHiLetgo #ad
ManufacturerHiLetgo #ad
Part Number3-01-1593



KOOKYE 5PCS Temperature Sensors TMP36 Precision Linear Analog Output For Arduino Raspberry Pi

KOOKYE #ad - 5pcs adi tmp36gz temperature sensors, High accuracy solid state temperature sensor. Outputs an analog voltage that is proportional to the ambient temperature. Voltage input: 2. 7v to 5. 5v dc, output range: 01v -40°c to 2. 0v 150°c. Temperature range: -40°c to 150°c / -40F to 302F 2°C accuracy.
BrandKOOKYE #ad
ManufacturerKOOKYE #ad
Part NumberTMP36



DEVMO DC 5V MAX6675 Module + K Type Thermocouple Temperature Sensor M6 Compatible with Ar-duino Raspberry Pi

DEVMO #ad - K type thermocouple junction location, use 301 ordinary terminals. 5v, working current 50mA. 0 ~ 5. Test temperature range: 0 Degree Celsious to 1024 degrees Celsious. Simple spi serial port temperature output. High-impedance differential inputs. Wide operating voltage range 3.
BrandDEVMO #ad
ManufacturerDEVMO #ad
Part Number7a6ab0a994c38907a20278aebe9841ef